NAIOA.comNAIOA.comNAIOA.com
 Create an Account
 

  
NAIOA Impala Forums :: View topic - Narrowing Down a P0336
GarageGarage    1/4 Mile Table1/4 Mile Table    Forum FAQForum FAQ    SearchSearch    UsergroupsUsergroups   MedalsMedals
MemberlistMemberlist   ProfileProfile    Watched TopicsWatched Topics    Log in to check your private messagesLog in to check your private messages    Log inLog in 

Narrowing Down a P0336

 
Post new topic   Reply to topic    NAIOA Impala Forums Forum Index -> 2000-2005 General Impala Discussion
View previous topic :: View next topic  
Author Message
00impala123
Senior Level
Senior Level
Bronze Contributor (Amount: 1) Bronze Contributor


Joined: Feb 01, 2010
Posts: 2653
Posts per day: 0.92
Location: Chicago, IL

2000 Chevrolet Impala


PostPosted: Thu Aug 12, 2010 8:40 pm    Post subject:  Narrowing Down a P0336 Reply with quote

Anybody have a how-to on figuring out what exactly is throwing a P0336 code? I know I could pull the possible parts, but since it could be a vast amount of things causing it, I figured there has to be a better method lol.

_________________
Back to top
View user's profile Send private message
IffyG
NAIOA Moderator
NAIOA Moderator
Silver Contributor (Amount: 1) Silver Contributor


Joined: May 19, 2007
Posts: 13731
Posts per day: 3.56
Location: Nashville, TN

2002 Chevrolet Monte Carlo
1998 Oldsmobile Intrigue
2009 Chevrolet Malibu


PostPosted: Fri Aug 13, 2010 1:34 am    Post subject:   Reply with quote

You probably need a new crank shaft position sensor. It's not uncommon for it to fail. I had to have one replaced in my Intrigue and I have had the one in my Monte Carlo replaced as well). Was pretty painless at the dealer, in and out for less than 300 bucks both times.

_________________
helldorado wrote:
GLWTGFY. Big Thumbs Up

Dan wrote:
Protip: If you don't know what you're doing, don't do it.


d
Back to top
View user's profile Send private message
04DetroitLS
Senior Level
Senior Level


Joined: Aug 10, 2004
Posts: 2560
Posts per day: 0.53
Location: Detroit

2004 Chevrolet Impala


PostPosted: Fri Aug 13, 2010 9:54 am    Post subject:   Reply with quote

its not that bad to change, go thru wheel well (remove wheel), pull belt(s) and pulley, remove collar, remove 2 bolts & replace

If you're going that far, you might as well do the CPS while you are in there. You'll need to do a case learn after too. Maybe 2hrs ish

If you dont have an Impact gun to remove the crank bolt (which is TTY and recommended to be replaced everytime) I can break the bolt free w/ a 1/2" breaker and my jack handle.... So it CAN be done

Also when replacing the pulley make sure to use your OLD crank bolt to seat the pulley, remove it THEN torque it

_________________
wanderson75 wrote:
shagnwagon wrote:
Your car makes small children cry. Laughing


His dog ran away and didn't come back for a few hours on the first fire up too. It was awesome.

When babies cry and animals flee, you know you did something right Laughing


Signature truncated by system. Maximum of 6 lines allowed
Back to top
View user's profile Send private message Send e-mail AIM Address Yahoo Messenger MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic    NAIOA Impala Forums Forum Index -> 2000-2005 General Impala Discussion All times are GMT - 4 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001, 2005 phpBB Group
Forums ©
All logos and trademarks in this site are property of their respective owner. Comments and posts are property of the poster. All other content is © 2008 by the NAIOA.


Use of this site constitutes agreement with the NAIOA Terms of Service (TOS)


PHP-Nuke Copyright © 2005 by Francisco Burzi. This is free software, and you may redistribute it under the GPL. PHP-Nuke comes with absolutely no warranty, for details, see the license.
Server Local Time: December 13, 2017, 10:22:49 pm
Page Generation: 0.10 Seconds ( SQL 21:105 in 0.02 Seconds )